Iraqi Journal of Science

An experiment is conducted to determine the effect of magnetic water on the production performance and blood characteristics of common quail, Coturnix coturnix (Linnaeus, 1758). The experimental treatments included T1 = control treatment, T2 = drinking water magnetization at1000 gauss, T3 = drinking water magnetization at 1500 gauss, T4 = diet sprayed with magnetized water 1000 gauss, T5 = diet sprayed with magnetized water 1500 gauss, each treatment with three replicates. The results showed significant superiority of control group in the body weight, weight gain and feed intake compared with treated groups. The egg shell thickness of T2 showed a significant decrease compared to other groups. The third treatment showed a significant superiority in red blood cell count compared with T1, T4 and T5, while T5 appeared significant reduction in white blood cell count compared with other treatments. There was significant reduction in blood glucose, total protein, cholesterol, and triglyceride in T4 compared with control.

The aim of the research was to assess effects of short and long-period exposure to radiation from mobile phone on blood indices in experimental rats. In this study forty mature female rats were used; the animals were divided into two experimental group, each group consists of twenty animals. Short-period group of rats were exposed to cell phone radiation for different duration 03 m, 63 m, and 03 m per day for six weeks. Long-period group of rats were exposed to radiation from mobile phone for different duration 2h, 4h, and 6h per day for three months. The study noticed that there was significant (P≥0.05) elevation in total white blood cells and the study demonstrated significant increment (P≥0.05) in percentage of lymphocytes (71.1%) of rats which exposed to radiation from mobile phone for short-period in (90 minutes) compared to the control group (42.64%). While, the study revealed that there was a significantly (P≥0.05) lower percentage of neutrophils (15.36%) in rats that were exposed to mobile phone radiation for long-period in (6 hours) compared with the control group (52.12%).The study recorded that there was a significant (P≥0.05) elevation in total red blood corpuscles and packed cell volume of rats exposed to radiation from mobile phone for short and long-period in different times compared with control. On the other hand, the research indicated that there was a significant (p≤0.05) decrement in mean corpuscles volume (MCV), mean corpuscle hemoglobin (MCH), mean corpuscle hemoglobin concentration and red blood cell distribution width standard deviation (RDW-SD) of rats to radiation from mobile phone for short and long-period in different times than control group.

Surface Plasmon Resonance (SPR) technology has been employed in biosensor applications and adapted to produce a sensitive optical sensor.. Simulation analysis ( using Matlab) has been done for SPR for gold (Au) layer with thickness (40 nm) and Polyvinyl Alcohol (PVA) polymer with various thickness (10, 20, 30, 40, 50, 60, 70 and 80 nm) deposited on glass prism type D-ZLAF50_Dense lanthanum flint. The sensitive layer was air (n=1). The analysis was taken for different wavelengths from ultra- violet of wavelength 100 nm to near infra- red wavelength of 1000 nm. The properties of θSPR was calculated from plots of reflectance against incident angle θincid.. The SPR sensitivity (S) was calculated. The results gave efficient detection in change of sensitive layer refractive index (0, 0.04, 0.08 and 0.12), the maximum obtained sensitivity was 207.5 for (PVA) thickness of 30 nm and 40 nm, Δn= 0.08 at wavelength 800nm and 1000nm, respectively. The best sensitivity in visible region (700 nm) was 158.33 for thickness 20nm, Δn= 0.12.

Surface plasmon resonance could increase the efficiency of solar cells , when light is trapped by the noble metallic nanoparticles arrangement at and into the silicon solar cell (SSC) surface. Pure noble metal (silver and gold) nanoparticles (NPs) have been synthesized as colloids in de-ionized water (DW) by pulsed laser ablation (PLA) process at optimum laser fluence. Silicon solar cell with low efficiency was converted to plasmonic silicon solar cell by overcasting deposition method of silver nanoparticles on the front side of the SSC. The performance of plasmonic solar cell (PSC) was increased due to light trapping. Two mechanisms were involved : inserting silver nanoparticles (Ag NPs) inside the silicon layer by the heating effect of pulsed laser and depositing gold nanoparticles (Au NPs) on the surface of the SSC by overcasting method. The optical properties of silver and gold colloidal solutions were studied with UV- Visible spectrophotometer with a range from 190 nm to 1100 nm. The absorption spectra showed single absorption peak located at about the characteristic value for silver and gold nanoparticles due to the surface plasmon resonance. Atomic Force Microscope (AFM) images were studied , the ablated noble NPs by pulsed laser have an average diameter less than 100 nm. AFM images showed the morphology of SSC surface without and with nanoparticles before and after overcasting and heating by laser methods. Electrical measurements for SSC namely current – voltage ( I-V )characteristics and responsivity (Rλ) displayed higher efficiency after these procedures. The efficiency rise to(5.2%) due to the localized surface plasmons excitation of (Ag NPs) that were embedded into the silicon layer by the heating effect of pulsed laser. The deposition of AuNPs on the silicon surface of the plasmonic SC additionally increased the efficiency to (7.28%), due to light trapping by scattering from Au NPs towards the plasmonic solar cell depth .

The knowledge of the quantity of total solar radiation on horizontal and inclined surfaces is very important in the calculations of heating and cooling loads in architecture and in the design of certain solar energy applications such as photovoltaic and solar collectors. This paper estimates the total solar radiation on inclined surfaces in Baghdad (Lat. 330 21' N 440 14' long and 34m above MSL). A good model was used to estimate hourly total solar radiation on the inclined surface with different elevations (150, 300, 450, 600, 750, 900) from a horizontal surface. The mean hourly, daily and monthly variation of total solar radiation on horizontal and inclined surfaces were drawn and discussed. The optimum tilt angle over a period of a year was drawn and discussed. Linear regression equations correlating the mean hourly solar radiation on an inclined surface with mean hourly solar radiation on a horizontal surface was deduced with high correlation coefficient (0.98 – 0.99)

Directing solar panels in a way that collects the largest possible amount of solar energy is still attracting a lot of attention due to the continuous need to get clean, inexpensive renewable energy. Iraq is one of the countries characterized by the abundance of solar energy but the investment in this field has been far below ambition. In this study, an application developed with the visual basic programing language was used to compute precisely various solar angles and parameters , as a powerful tool for engineers and researchers. The outputs of the model were tested and discussed in detail. The air mass values were also computed for three cities: Mosul, Baghdad, and Basra. The results showed that the best time to acquire the solar radiation would be from 10 am to 2 pm (local time), the period that has the lowest values of air mass. Additional useful calculations that can be estimated by the application were the terrestrial irradiances from four empirical models for the clear sky: Roledo-Soler, Adnot, Kasten – Czeplak, and Berger-Duffie. The calculated values of terrestrial irradiance were compared with observed data measured by automatic weather station. The application simulated the actual values with some deviations due to the existence of clouds and aerosols. Kasten – Czeplak model was recommended to be used in Iraq since it was the best model to simulate the measured values. The comparison between the model’s output and the measured values on a daily basis on the 21st of June showed good agreement. The study suggested that the solar panels should face the south direction with a change of the tilt angle of the panels from 25o in June to a value of 60o each month towards the coldest months by an increment of 5 degrees.

As part of our research on efficiency improvement of PERC (Passivated Emitter Rear Solar Cell), achieving very low reflectivity values of solar cell surface is a must. One of the most advance technologies to do so is the use of advanced texturing for the front surface of the cells. This texture, also known as Black Silicon, consists of peaks and valleys of nano metric dimensions and capable of dramatically reducing the reflectance of the front surface. A reflectance around 5% was reached ,using simulation, when using a Black-Silicon texturing with height of 50nm with peak rounding of 5nm. Even though this texturing may affect other parameters such as series resistance or surface recombination, as a starting point, simulation was used to find the optimum peak rounding, where the radius of curvature of the peak is maximum, while keeping reflectance as low as possible.

In this work proton exchange membranes were prepared by a modified microwave casting solution technique, using the polymers blend (polyethersulfone (PES), polystyrene (PS), polyvinylidenefluride (PVDF)). Modified casting method was used to overcome the poor compatibility between hydrophilic, (PES, PS) and hydrophobic PVDF, by cooling the substrate during the film casting process to (4.5-5.5oC). Membranes were chemically modified by three reaction types to study the differences between their effects on the required properties for microbial fuel cell application. These methods use blend organic sulfonic acid precasting process and sulfonation by sulfuric acid post-casting process (APS), blending organic sulfonic acid precasting process (AS) and sulfonation by sulfuric acid post-casting process (AP). The presence of organic sulfonic acid and the sulfonation were confirmed via FTIR spectra for the membranes. The membranes were characterized by proton conductivity, ion exchange capacity (IEC), [-SO3H] value, and water uptake. MFC is characterized by electrochemical polarization tests and power densities obtained from it were used to evaluate the efficiency of the membrane in the cell.

In this study, water was heated using solar energy . This research presents the design and experimental analysis for using Spiral Flow Solar Water Heater (SFSWH) to enhance thermal efficiency of a flat plate solar collector. A solar water heater consisting of a copper tube in the shape of a spiral was fixed on an iron flat plate as an absorber. The experiment also included the selection quality of the paint used to dye the absorbent surface. In May at Fallujah (33.34ºN, 43.8ºE), the thermal performance was calculated. The maximum temperature difference in the storage tank of about 18 ℃ for (SFSWH) during the experimental time was obtained. The obtained efficiency of the collector was about (80.11%). The SFSWH gave an increase of (40 %) in its efficiency compared to published values.

Twelve cigarette tobacco samples of various brands and origins were gathered from local markets of Iraq. . The CRn was determined utilizing CR-39 track detectors which were exposed to the various brands of cigarettes tobacco for 45 days. The results demonstrated that the highest value of 222Rn concentration was )157 Bq/m3( in Macbeth cigarette sample of Brazilian origin and the lowest value of CRn was (76.3 Bq/m3 ( in Sumer cigarette sample of Iraqi origin,with an average value of (106.53±22.3 Bq/m3). The outcomes have demonstrated that cigarettes of a Brazilian origin contain higher CRn than other studied samples, however, it is still less than some other average values given in the literatures.

Forty-four bottles of drinking water were collected from the local markets of Basra City and stored in the laboratory refrigerator at 4ºC until the physical, chemical and biological measurements were carried out. The results showed a discrepancy in the compatibility of the specifications written on the drinking water bottle label with the sample measurements as well as the variation in the results with the Iraqi standards for bottled water. The percentage of bottled water that is not safe for drinking was 88.5% of the total samples of the study. This value is high and an indication of lack of control over marketing from the imported or produced in the local labs, so it is a danger to the health of the consumer. Results showed that the PH ranged 6.5–8 and did not exceed the values on the information sheet of the potable drinking water as well as the TDS, chloride, magnesium; nitrate and potassium which were within the permissible limits. In addition, the results showed that calcium, total hardness, fluoride and bacterial growth values exceeded the permissible limits, and there are different significations between factors in samples.

The subject of biophysics is interdisciplinary and covers various fields of biology and physics. In this research the effect of some parameters of Nd:YAG laser on ants (Camponotus consobrinus) has been studied . This includes the effect on its external shape, as well as the percentage of the killing rate obtained. A laser radiation of a wavelength (1.064 μm) with different energies: (300, 320, 340, 360, 380 and 480 mJ) was used to irradiate ants placed at a distance of (10 cm) distance from the laser source . The irradiation times were (15 and 20 sec) for each energy. The obtained results showed an increase in the rate of ant mortality, as well as an increase in deformations, as the laser energy and the irradiation time increased. These results were recorded after different time periods (12, 24, 48 and 72 hours) after laser treatment.. The thermal diffusion within the tissues resulting from laser radiation causes increased death rates due to damage of internal structures.

CdSe/CdS Core/shell nanostructures were prepared through the chemical synthesis method. XRD ,EFSEM and TEM investigations confirmed the formation of core/shell structure for the sample. The AFM measurement was employed to reveal the morphology of the prepared thin films. Optical characterizations of the quantum dots were done by UV-visible and photoluminescence spectra. It was found that the quantum dots prepared has good optical properties. Due to the presence of shell coating on core CdSe, the energy gap of the core/shell nanomaterial were increased from 2.2 to 2.3eV. The resulted QDs are a promising candidate for photovoltaic and biosensor applications.

Nickel nanoparticles (Ni-nanoparticles) were incorporated as an antecedent utilizing nickel acetate and as a reducing agent, extraction plantApiumgraveolens. The reason fo choosing this plant over many other is because it is easily accessible, carries many antioxidants, non-toxic, and there are no dangerous residues and stabilizing agent at 60℃ under stirrer. The progress of the reaction was monitored by observing a change in color of the obtained solution. The UV–Vis utilized to screen the development of Ni-nanoparticles inside a surface plasmon band (SPB) at 275 nm gives a phantom mark appropriate to the arrangement of nanoparticles. Examining the electron microscope (SEM) photos showed the Ni-nanoparticles to be of cubic shape with sizes in te range of (6-45 nm). GC-MS s spectra were utilized to show the debasement when the expansion of nickel nanoparticles. The most noteworthy accessibility of aliphatic mixes at the hour of (1.3, 1.46, 1.62, 12.04) min. In the interim after the expansion of nanoparticle, the outcomes show a high bounty at (1.29, 2.1) min. The importance of this research lies in the possibility of breaking large organic compounds into simpler compounds, as the presence of large organic compounds with high molecular weights leads to pollution of sea and ocean waters when poured into it as a result of sea transport.

The ferric oxide nanoparticles (Fe2O3) which are deposited at interface which is related to hole collecting buffer layer [poly(3,4-ethyl-enedioxythiophene): poly(styrene-sulfonate) (PEDOT: PSS)] as well as regioregular poly(3-hexyl-thiophene): Zinc oxide nanoparticles (P3HT): (ZnO) active layer have been considerable increasing the performance of solar cell. Also, the solar cell devices have been fabricated with a weight ratio of 1:0.7, 1:0.8, 1:0.9 and 1:1 of P3HT and ZnO, respectively. In addition, photo physical characteristics regarding such devices with different value of the weight ratio were examined. This work is indicating that the absorption spectrum related to blend will be broad with varying ratios that was extremely required for the devices of the organic solar cells. Furthermore, the film morphology was estimated via atomic force microscope (AFM). EQE (i.e. External quantum efficiency) and XRD patterns measures were achieved for the optimal device, while the improvement in the efficiency with regard to a device with 1:1 was more considerable compared to 1:0.90, 1:0.80 as well as 1:0.70 values of weight ratio of P3HT and ZnO. With different weight ratio values, a solar cell upon (1:1) provides PCE (i.e. Power Conversion Efficiency) of 4.1%, dissimilar to 3.92% for (1:0.9), 3.9% for (1:0.8) and 3:6% devices.

In this work, the electrical properties and optimum conditions of the plasma sputtering system have been studied. The electrical properties such as Paschen's curve, current-voltage, current pressure relations, the strength of magnetic field as a function of inter-electrode distance, the influence of gas working pressure and argon-oxygen ratio on the electrical characterization were studied to determine the basic optimum condition of the system operation. the discharge current as a function of discharge voltage showed high discharge current at 2.5 cm. These parameters represent the basic conditions to operate any plasma sputtering system which are the right behavior to build up and design the discharge an electrode. The ideal conditions of these homemade systems were qualified to prepare the various nanostructure thin films. The two electrodes were made of copper because of its good conductivity, and to avoid the power dissipation inside discharge chamber.

Current study was carried out to determine the adsorption ability of the Multiwall carbon nanotubes (MWCNTs) by adsorption Malachite Green dye from an aqueous solution. Crystal structure of the materials was measured using powder X-rays diffraction (PXRD), UV–Vis diffuse reflectance and specific surface area (BET). Many parameters that affecting the adsorption process such as contact time, pH, adsorbent dosage, initial dye concentration and temperature were studied. The outcome showed that an increasing occurred in the adsorbent dosage and the rate of dye removal, and the best efficiency for Malachite Green dye removal was amounted 99. 11 %. The results were obtained at optimal reaction conditions were pH = 5.5, catalyst weight 0.15 g, T = 298 K and reaction time = 1 h. In addition, the equilibrium adsorption isotherms and kinetics studies were investigated using Freundlich and Langmuir isotherms. The Freundlich isotherm (R2=0.9506) was found to be the best fitted for experimental data of this study .A higher correlation value of kinetic model was observed close to pseudo-second-order (R2=0.999) compared to other kinetic models.

Chromium oxide nanoparticles were synthesized using cauliflower extract by two methods: simple chemical method and the sol-gel method. These technologies are new, environmentally friendly and cheap. Cauliflower contains plant materials and biomolecules (chromium, phenols, alkalis, vitamins, amino acids, quinones, etc .
(that convert chromium chloride hexahydrate (CrCl3.6H2O) into chromium nanoparticles. The plant extracts also act as diluents, stabilizers and anti-caking agents. X-ray diffraction (XRD) analysis showed that the size of the crystals decreased from (36.1 to 57.8) nm using the simple chemical method to (13.31 to 20.68) nm of Cr2O3 using sol-gel. The scanning electron microscopy (SEM) showed that Cr2O3 NPs of the simple chemical method were Nano layers with (130.3) nm, while the Cr2O3 NPs of the sol-gel method were spherical or semispherical in shape with a particle size of (14.89 to 39.08) nm. The results obtained have no matches in the reported literature.. Ultraviolet-visible (UV-Vis) showed that the band gap energy of Cr2O3 NPs of the simple chemical method was 2.5 eV, while it was 3.4 eV for Cr2O3 NPs of the sol gel method . Cr2O3 NPs of high purity , small particle size, and large energy gap were obtained from the sol-gel method This means that the NPs from the sol gel method were better than those of the simple chemical method. The study revealed that the Chromium oxide nanoparticles synthesized using cauliflower extracts could be used as antibacterial agent for human pathogenic
bacteria

In this paper, thin films of undoped and nickel oxide (NiO) doped titanium dioxide (TiO2) were prepared using the chemical spray pyrolysis deposition (CSP) technique, with different concentrations of nickel oxide (NiO) in the range (3-9) wt%. The morphological, structural, electrical, and sensing properties of a gas of the prepared thin films were examined. XRD measurements showed that TiO2 films have a polycrystalline structure. AFM analysis showed that these films have a regular structure both before and after doping . The roughness of these films decreased after adding impurities but then the opposite of that took place. The electrical and gas sensing properties of titanium dioxide was also affected after doping. The highest sensitivity value was obtained at doping concentration of 5wt% and working temperature 473ºK.

The fatigue is one of the major reasons for fracture of materials. Aluminum 7204 AA alloy with various heat treatments and (2.0) wt % of SiC nanoparticles were prepared by stir-casting method under rotating bending loading with ratio of stress (R= -1). The composite was strengthened by SiC particles size of) 10 (nanometre. The fatigue strength and life were obtained experimentally by the family of S-N curves for different heat treatments. The endurance limits (107cycles) for 7204 AA/ 2.0wt% SiC nano-composite fatigue strength as related to untreated nanocomposite was enhanced by 72 and 78.5% for T4 and T6, respectively.The improvement of fatigue properties is due to better spreading of SiC nanoparticles and increased porosity.

The experiment was conducted at the Agricultural Research Office in Baghdad during July 2020 to test the ability of nanomaterials (ZnO and TiO2) to inhibit ochratoxin A, which is produced by a number of microbiology (fungi) including: Aspergillus ochraceus, A. niger, ,A. steynii, A. carbonarius, Pencillume verrucosum and P. nordicum. The standard ochratoxin A, with known concentration, was treated with different concentrations of nanomaterials (20, 40, 60, and 80 ppm) and two different particle sizes of nanoparticles approximately (15 nm) and (70 nm) for each (ZnO) and TiO2; with 16 transactions. Through an examination of the HPLC, the results showed that all transactions led to a noticeable inhibition in the concentration of ochratoxin A, and the highest inhibition rate was for ZnO nanoparticles with particle-size (70 nm) and 80 ppm concentration, where the inhibition rate was 99%. In other hand, the TiO2 nanoparticles with particle-sized (70 nm) and the concentration (80 ppm) were followed by 95%.

In this study the as-deposited and heat treated at 423K of conductive blend graphene oxide (GO)/ poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) thin films was prepared with different PEDOT:PSS concentration (0, 0.25, 0.5, 0.75 and 1)w/w on pre-cleaned glass substrate by spin coater. The XRD analysis indicate the existence of the preffered peak (001) of GO around 2θ=8.24° which is domain in all GO/ PEDOT:PSS films characterized for GO, this result approve the good quality of the PEDOT:PSS dispersion in GO, this peak shifted to the lower 2θ with increasing PEDOT:PSS concentration and after annealing process. The scanning electron microscopy (SEM) images and atomic force microscopy (AFM) clearly show the GO flakes and go to disappear with increasing the PEDOT:PSS concentration.

In this study, titanium dioxide (TiO2( are synthesized by sol– gel simple method. Thin films of sol, gel, and sol- gel on relatively flat glass substrates are applied with Spin coating technique with multilayers. The optical and morphological properties (studied using AFM) of TiO2 layers show good properties, with particles diameters less than 4 nm for all prepared samples and have maximum length 62 nm for TiO2 gel thin films of three layers. The results show low roughness values for all films especially for 4 layers sol (8.37nm), which improve the application in dye sensitive solar cell (DSSc)

Three different rotational speeds (800, 1000 and 1250 rpm) and traverse speeds of (0.42 mm/sec) at a constant taped pin have been employed to produce the stir zones generated from friction stir processing (FSP) of near eutectic Al- 14 wt.% Si alloy. The processed samples were thoroughly analyzed macroscopically and microscopically. The as-cast microstructure of eutectic (α Al+ Si) and primary Si were fragmented to produce spheroidization of small size of Si and deformed matrix. The stir zones showed an increase in hardness from around 45-50 Hv for as-cast to 40-65 depending on the variables applied. All the processed samples were characterized by advanced and retreated regions with large single piping defects formed mainly at the retreated region. High temperature spheroidization at 500 oC with two soaking times of 10 and 20 hrs was applied for the processed sample of 1000 rpm to investigate the effect of heat treatment on the silicon fragmentation and hardness. Growth and fragmentation of Si have taken place at soaking time of 10 hrs. At soaking time of 20 hrs noticeable microvoids and macrovoids were formed at the stir zones. Microhardness of both the advancing and the retreating regions decreased with increasing soaking time.

Ultrasound imaging has some problems with image properties output. These affects the specialist decision. Ultrasound noise type is the speckle noise which has a grainy pattern depending on the signal. There are two parts of this study. The first part is the enhancing of images with adaptive Weiner, Lee, Gamma and Frost filters with 3x3, 5x5, and 7x7 sliding windows. The evaluated process was achieved using signal to noise ratio (SNR), peak signal to noise ratio (PSNR), mean square error (MSE), and maximum difference (MD) criteria. The second part consists of simulating noise in a standard image (Lina image) by adding different percentage of speckle noise from 0.01 to 0.06. The supervised classification based minimum distance method is used to evaluate the results depending on selecting four blocks located at different places on the image. Speckle noise was added with different percentage from 0.01 to 0.06 to calculate the coherent noise within the image. The coherent noise was concluded from the slope of the standard deviation with the mean for each noise. The results showed that the additive noise increased with the slide window size, while multiplicative noise did not change with the sliding window nor with increasing noise ratio. Wiener filter has the best results in enhancing the noise.

Evapotranspiration (ET) is produced from vegetation transpiration and soil evaporation. The ET measurements must be considered to study water management systems and irrigation (planning, designing and operating). This study is based on USGS (United States Geological Survey) data by the SSEBop (Simplified Surface Energy Balance) model to estimate the total annual amount of ET using ArcGIS software. The ET values were determined for seventeen years from 2003 to 2019. Also, these values for year 2020 were estimated based on the value of the monthly ET for seven months, i.e. until August by summation. The field data of gauge stations spread throughout Iraq for the year 2012 were used to verify the ET values for the same year. There was distinct compatibility between them. For the four years 2017, 2018, 2019 and 2020, the area of zero ET was a little more than half the area of Iraq (56%). While the years from 2003 to 2016, the average percentage of the area was about 24% of Iraq’s area. For classification for ET values 0 - 50 mm, the area percentage was 29% of total area for years from 2003 to 2016, while from 2017 to 2020 the percentage was 10%. The ET values of 50-100 mm have an area ratio of 12% of total area for years 2003 to 2016, while the percentage was 4% for the remaining years. For all years of study, the area percentage was approximately the same for ET values greater than 100 mm. The study recommends increasing the water quotas and speeding up the construction of strategic projects in Iraq to compensate the shortage of vegetation cover, especially in last the four years, more than half of the area had ET values equal to zero.

One of the serious environmental challenges that Iraq faces is climate changes and impacts of changing weather patterns and extreme global weather events. This paper addresses changes in the temporal and spatial characteristics of water levels of Razzaza Lake and response to climatic changes using archived series of Multispectral satellite images Landsat. TM, ETM+ and OLI images acquired on 1990, 2000 and of 2016. In order to extract, mapping the water surface area of the Razzaza Lake, Multispectral spectral band rationing the Normalized Difference Water Index (NDWI) technique was adopted, and the climatic elements data for the period (1990-2016) were analyzed which provide significant information of surface water. The results show that Razzaza Lake has a particularly sharp change rate in the water level and there are significant fluctuations on lake level and water surface area over the time.

Urban design and human activity are main causes of environmental pollution and climate change, such as reliance on energy production plants, factories and transportation that depend on fossil fuels, in addition to transformation of most green areas into residential areas. This paper aims to establish a sustainable city with an environment friendly urban design that contributes to exploitation of natural resources in the generation of electric power, use of green means of transport and thus the reduction of pollution. Anah site was chosen as the best site for designing a sustainable city, with its natural resources, air quality and moderate climate. The total area of the city is 9990187m2 divided into seven main parts, which include residential area, green areas, agricultural areas, public areas, wind farm, industrial area, and solar collecting area. SAM software has also been used in the city's renewable energy accounts. It was found that the annual output of the wind farm consisting of 15 turbines is 71080608 kWh and the power factor ratio is 36.1%. While the annual production of solar energy for each house was equal to 12527 kWh and the power factor was 23.8%.

Predicting weather by numerical models have been used extensively in research works for Middle East, mostly for dust storms, rain showers, and flash floods with a less deal of interest on snow precipitation. In this study, the Global/Regional Integrated Model System (GRIMs) that was developed in South Korea was used to predict a rare snowfall event occurred in three countries in Middle East (Syria, Jordan and Iraq) located between (25-65 oE; 12-42 oN) in year 2008. The main aim of this study was to test GRIMs efficiency, which would be used for the first time in Middle East, to make predictions of weather parameters such as pressure, temperature, and relative humidity especially in the selected area. In addition, the study would investigate the conditions that caused the snowfall event. GRIMs model was installed, compiled, and run on a Linux platform by using NCEP-NCAR reanalysis dataset as initial conditions on 0.5 × 0.5 grid resolution to make simulations for three days at intervals of three hours. The output of the model was evaluated by making comparisons with actual data obtained from the GFS Agency dataset and the model showed its efficiency. The snowfall event was synoptically discussed in details. It was found that the snowfall event was a result of fast succession systems of a strong cold high pressure and then a deep warm low pressure. The high instability in the region had led to form large cumuliform clouds with snow precipitation as a rare event in very long period.

Carbon Monoxide (CO) has a significant indirect effect on greenhouse gasses due to its ozone and carbon dioxide precursor, and its mechanism of degradation involving the hydroxyl radical (OH) which control the oxidizing ability of the tropospheric. To understand the effect of human activities on atmospheric composition, accurate estimates of the sources of atmospheric carbon monoxide (CO) are necessary. MOPITT (Measurements of Pollution in the Troposphere) is a NASA Terra satellite instrument designed to allow both Thermal-Infra-Red (TIR) and Near-Infra-Red (NIR) observations to be used to collect vertical CO profiles in the Troposphere via the concept of correlation spectroscopy. The objective of the current study is to analyze and map the monthly, seasonal and annual trend of CO concentration for year 2016 in Nineveh governorate using the retrieved CO Surface Mixing Ratio Day mode of level 3, version 7 dataset. The dataset was downloaded from the National Aeronautics and Space Administration (NASA) operated GIOVANNI portal. The results of dataset analysis in GIS software showed many sources of carbon monoxide in Nineveh Governorate, which change with months and seasons of the year. Generally, the observed CO concentration levels in the southern and western of the governorate were more than in the northern and eastern parts. The annually average CO ranges from (115.374 ppbv) to (132.452 ppbv). Also, CO emissions and concentrations were higher in winter (128.638-157.567 ppbv) than summer season (97.144-106.515 ppbv).

Culture heritage reflects nation’s legacy and therefore should be protected from damage in order to pass it to future generations. Recently, such protection can be applied by 3D digitization techniques such as conservation, restoration, documentation, etc. The 3D digitalization of heritage assets has encountered numerous focus in the last two decades due to the development in data capturing techniques and technological advancement in 3D remote sensing (RS) approaches such as photogrammetry and laser scanning. However, the abundance of 3D information resources and spatial data modelling and analysis methods have urged stakeholders to adopt intelligent 3D data management system so called Building Information Modelling (BIM) to facilitate data approaching and management. Historic Building Information Model (HBIM) is a special case of the BIM system, however it reflects the possibility to apply the BIM technology to the historical and heritage buildings. In this research, Structure from motion (SfM) photogrammetric routine based on Unmanned Aerial Vehicles (UAVs) images was applied to build HBIM of the Great Ziggurat of Ur in the south of Iraq. Based on the 3D geometric and texturing information extracted through photogrammetry and the historical information provided, virtual reconstruction has been carried out using (HBIM) technology. This was achieved by applying realistic materials and texturing information in order to document the building, which is directed to investigate the feasibility of implementing image-based 3D modelling within HBIM environments. Restoring the missing parts of the Ziggurat temple was also a focus of this research by implementing reverse engineering methodologies based on available information considered within the extracted HBIM. This can successfully represent a complete virtual reality model and a management information system of the Ziggurat building to be passed to future generations. The work also includes data assessment and validation with the as-built model generated from reference measurements within Computer Aided Design (CAD) environment.

Many satellite systems take cover images like QuickBird for terrain so that these images scan be used to construct 3D models likes Triangulated Irregular Network (TIN), and Digital Elevation Model (DEM). This paper presents a production of 3D TIN for Al-Karkh University of Science in Baghdad - Iraq using QuickBird image data with pixel resolution of 0.6 m. The recent generations of high-resolution satellite imaging systems open a new era of digital mapping and earth observation. It provides not only multi-spectral and high-resolution data but also the capability for stereo mapping. The result of this study is a production of 3D satellite images of the university by merging 1 m DEM with satellite image for ROI using ArcGIS package Version 10.3.

The objective of this study is to select a suitable observing region at Baghdad location (44o 22' 48", 33o 16' 30") with low interference that may affect frequency of 1.42 GHz. Baghdad University Radio Telescope (BURT) is used in this study to determine a convenient region for observation in Baghdad sky. Different azimuths and elevations were chosen at different observations time. The results of this study showed that the best observations regions were located at azimuth (120o-160o) and (210o-260o). These regions included less sky temperature and estimated to be (42.8 to 163) K. The sky temperature model could be represented as a polynomial of third
degree that could fit the behavior of the observation points.

Drought is a complex phenomenon that has severe impacts on the environment. Vegetation and its conditions are very sensitive to drought effects. This study aimed to monitor and assess the drought severity and its relationships to some ecological variables in ten districts of Erbil Governorate (Kurdistan Region), Iraq, throughout 20 years (1998-2017). The results revealed that droughts frequently hit Erbil throughout the study period. The Landsat time-series- based on Vegetation Condition Index (VCI) significantly correlated with precipitation, Digital Elevation Model (DEM), and latitude. Extreme VCI-based drought area percentages were recorded in 1999, 2000, 2008, and 2011 by 43.4%, 67.9%, 43.3%, and 40.0%, respectively. The highest crop yield reduction in the study area occurred mainly in 2000, 2008, and 2012 due to low precipitation rates. These results reveal the capability of the VCI for drought characteristics and highlighting relationships with some ecological variables, which provide vital information to the decision-makers, environmental, and economic sectors.

Today, Unmanned Aerial Vehicles (UAVs) or Drones are a valuable source of data on inspection, surveillance, mapping and 3D modelling matters. Drones can be considered as the new alternative of classic manned aerial photography due to their low cost and high spatial resolution. In this study, drones were used to study archaeological sites. The archaeological Nineveh site, which is a very famous site located in heart of the city of Mosul, in northern Iraq, was chosen. This site was the largest capital of the Assyrian Empire 3000 years ago. The site contains an external wall that includes many gates, most of which were destroyed when Daesh occupied the city in 2014. The local population of the city of Mosul has also largely overtaken the central part of this archaeological site, while the northern and southern parts are still uninhabited. The awareness of the existence of unchanged surface and ground forms in the northern or southern parts led us to prepare an urgent study to interpret the outer surface of those parts and to analyze any discovery in the surface morphology. So, drone data and GIS technologies were used in this study to find any discovery that could aid in understanding the original surface of this ancient site. Visual and digital interpretations of satellite images, drone images, and Digital Surface Models (DSMs) were used to analyze and study the data. As a final result, certain morphological features were identified in the southern parts of the ancient site which could be a new archaeological and compositional discovery with reference to the earlier activities of the ancient society during the Assyrian empires, represented by the ditches and building lands used by the ancient inhabitants. Small modern tunnels penetrated the ancient wall were also discovered in addition, to a drainage canal and a motorway newly constructed during the occupation of the city that had penetrated the archaeological land.

Recently, renewable energy (RE), such as solar energy, sources have proven their importance as an alternative source of fuel. The utilizing of solar energy can contribute to move the world towards relying on clean energy to curb global warming. However, the placement of solar farms is a major priority for planners as it is a critical factor in the succession energy project. This study combines one of the multi-criteria decision-making techniques Analytic Hierarchy Process (AHP) and Geographic Information System (GIS) to assess the suitability of land for establishing solar farms in Iraq. Numerous climatic, geomorphological, economic, and environmental criteria and some exclusionary constraints have been adopted in modeling process. It is supported by expert knowledge and a comprehensive literature review. The results showed that approximately 19% of the study area are optimal areas for installing solar farms. The southern, southeastern, and a few western regions obtained the largest part of the suitable lands. Furthermore, this approach can be adapted easily to cover different criteria and different weights in order to assist planners in deciding solar farm locations.

Human eye offers a number of opportunities for biometric recognition. The essential parts of the eye like cornea, iris, veins and retina can determine different characteristics. Systems using eyes’ features are widely deployed for identification in government requirement levels and laws; but also beginning to have more space in portable validation world.
The first image was prepared to be used and monitored using CLAHE which means (Contrast Limited Adaptive Histogram Equalization) to improve the contrast of the image, after that the 3D surface plot was created for this image then different types of regression were used and the better one was chosen.
The results showed that power regression is better, and fitter than other fitting methods (8th, 7th, 6th, 5th, 4th, 3rd, 2nd) degree polynomial, and straight line respectively, when depending on the sum of residual squared.
The estimations of R-square demonstrated that (5th, 6th, 7th, 8th) have a great proportion of variance in the model followed by (power, 4th, 3rd, 2nd, straight line) respectively. The conclusion from these results is that the power regression has a better fitting than other types of fitting functions for this study and similar ones.