Iraqi Journal for Electrical And Electronic Engineering

To gain insight into complex biological endocrine glucose-insulin regulatory system where the interactions of components of the metabolic system and time-delay inherent in the biological system give rise to complex dynamics. The modeling has increased interest and importance in physiological research and enhanced the medical treatment protocols. This brief contains a new model using time delay differential equations, which give an accurate result by utilizing two explicit time delays. The bifurcation analysis has been conducted to find the main system parameters bifurcation values and corresponding system behaviors. The results found consistent with the biological experiments results.

This paper proposes a low-cost Light Emitting Diodes (LED) system with a novel arrangement that allows an indoor multi-robot localization. The proposed system uses only a matrix of low-cost LED installed uniformly on the ground of an environment and low-cost Light Dependent Resistor (LDR), each equipped on bottom of the robot for detection. The matrix of LEDs which are driven by a modified binary search algorithm are used as active beacons. The robot localizes itself based on the signals it receives from a group of neighbor LEDs. The minimum bounded circle algorithm is used to draw a virtual circle from the information collected from the neighbor LEDs and the center of this circle represents the robot’s location. The propose system is practically implemented on an environment with (16*16) matrix of LEDs. The experimental results show good performance in the localization process.

In this paper, the vector-controlled Permanent Magnet Synchronous Motor (PMSM) fed by Indirect Matrix Converter (IMC) is analyzed, designed, and simulated by using the IMC with Carrier Based Pulse Width Modulation (CBPWM). The CBPWM strategy is based on Space Vector Pulse Width Modulation (SVPWM) analysis, it is used to enhance the input current waveform, reduce the complexity of switching signals generation, and to solve the commutation problem. The traditional PMSM drive system is simulated for comparison with proposed drive system. The proposed drive system is compared to the traditional drive system using the Total Harmonic Distortion (THD). The comparison results show that the proposed drive system outperform the traditional drive system by THD different of 1/30 of input current and 1/1.5 of stator current, with high input power factor.

The scarcity of clean water resources around the globe has generated a need for their optimum utilization. Internet of Things (IoT) solutions, based on the application-specific sensors’ data acquisition and intelligent processing, are bridging the gaps between the cyber and physical worlds. IoT based smart irrigation management systems can help in achieving optimum water-resource utilization in the precision farming landscape. This paper presents an open-source technology-based smart system to predict the irrigation requirements of a field using the sensing of ground parameters like soil moisture, soil temperature, and environmental conditions along with the weather forecast data from the Internet. The sensing nodes, involved in the ground and environmental sensing, consider soil moisture, air temperature, and relative humidity of the crop field. This mainly focused on wastage of water, which is a major concern of the modern era. It is also time-saving, allows a user to monitor environmental data for agriculture using a web browser and Email, cost-effectiveness, environmental protection, low maintenance and operating cost and efficient irrigation service. The proposed system is made up of two parts: hardware and software. The hardware consists of a Base Station Unit (BSU) and several Terminal Nodes (TNs). The software is made up of the programming of the Wi-Fi network and the system protocol. In this paper, an MQTT (Message Queue Telemetry Transportation) broker was built on the BSU and TU board.

The Intelligent Control of Vibration Energy Harvesting system is presented in this paper. The harvesting systems use a mechanical vibration to generate electrical energy in a suitable form for use. Proportional-Integrated-derivative controller and Fuzzy Logic controller have been suggested; their parameters are optimized using a new heuristic algorithm, the Camel Traveling Algorithm(CTA). The proposed circuit Simulink model was constructed in Matlab facilities, and the model was tested under various operating conditions. The results of the simulation using the CTA was compared with two other methods.

In this paper, three phase induction motor (IM) has been modelled in stationary reference frame and controlled by using direct torque control (DTC) method with constant V/F ratio. The obtained drive system consists of nine nonlinear first order differential equations. The numerical analysis is used to investigate the system behavior due to control parameter change. The integral gain of speed loop is used as bifurcation parameter to test the system dynamics. The simulation results show that the system has period-doubling route to chaos, period-1, period-2, period-4, and then the system gets chaotic oscillation. A specific value of the parameter range shows that the system has very strong randomness and a high degree of disturbance.

Swimming performance underlies the biomechanical properties and functional morphology of fish fins. In this article, a pair of concave fin has been suggested, which is inspired from Labriform-mode Swimming fish. First, three concave fins with different sizes are proposed in order to choose the optimum size. All three fins have the same length but with different surface areas, such that each fin has an aspect ratio different from the others. Next, the complete design of the robot is suggested, the complete design of the body and pectoral fins were subjected to computational fluid dynamics (CFD) analysis to show the validity of the proposed model. Finally, the physical model is suggested and provided with 3D printer of Polylactic Acid (PLA) with a density of 1240 kg/ m3. The swimming robot fins have been examined by CFD analysis provided by Solidworks® to evaluate the highest thrust and lowest drag forces. The result showed that the optimum fin is the one with the lowest aspect ratio fin produces the highest drag, whereas the highest aspect ratio fin gives the lowest drag and thrust, therefore; a value of aspect ratio in between these two cases is chosen. While other types of examinations are based on motion analysis of the 3D design, the required motor torque is calculated in order to select a suitable servomotor for this purpose, which a HS-5086WP waterproof servomotor can achieve the calculated torque.

In recent years, the number of researches in the field of artificial limbs has increased significantly in order to improve the performance of the use of these limbs by amputees. During this period, High-Density surface Electromyography (HD-sEMG) signals have been employed for hand gesture identification, in which the performance of the classification process can be improved by using robust spatial features extracted from HD-sEMG signals. In this paper, several algorithms of spatial feature extraction have been proposed to increase the accuracy of the SVM classifier, while the histogram oriented gradient (HOG) has been used to achieve this mission. So, several feature sets have been extracted from HD-sEMG signals such as; features extracted based on HOG denoted by (H); features have been generated by combine intensity feature with H features denoted as (HI); features have been generated by combine average intensity with H features denoted as (AIH). The proposed system has been simulated by MATLAB to calculate the accuracy of the classification process, in addition, the proposed system is practically validated in order to show the ability to use this system by amputees. The results show the high accuracy of the classifier in real-time which leads to an increase in the possibility of using this system as an artificial hand.

his work deals with the simulation model of multi-machines system as cold rolling mill is considered as application. Drivers of rolling system are a set of DC motors, which have extend applications in factories as aluminum rolling. Interconnection of multi DC motors in such a way that they are synchronized in their rotational speed. In cold rolling, the accuracy of the strip exit thickness is a very important factors. To realize accuracy in the strip exit thickness, Automatic Gauge Control system is used. In this paper MATLAB/SIMULINK models are proposed and implemented for the entire structures. Simulation results were presented to verify proposed model of cold rolling mill.

In order to mitigate the effect of voltage sag on sensitive loads, a dynamic voltage restorer (DVR) should be used for this purpose. The DVR should be accompanied with a fast and accurate sag detection circuit or algorithm to determine the sag information as quickly as possible with an acceptable precision. This paper presents the numerical matrix method as a distinctive candidate for voltage sag detection. The design steps of this method are demonstrated in detail in this work. The simulation results exhibit the superiority of this technique over the other detection techniques in term of the speed and accuracy of detection, simplicity in implementation, and the memory size. The results also accentuate the recognition capability of the proposed method in distinguishing different types of voltage sag by testing three different voltage sag scenarios.

CMOS stack circuits find applications in multi-input exclusive-OR gates and barrel-shifters. Specifically, in wide fan-in CMOS NAND/NOR gates, the need arises to connect a relatively large number of NMOS/PMOS transistors in series in the pull-down network (PDN)/pull-up network (PUN). The resulting time delay is relatively high and the power consumption accordingly increases due to the need to deal with the various internal capacitances. The problem gets worse with increasing the number of inputs. In this paper, the performance of conventional static CMOS stack circuits is investigated quantitatively and a figure of merit expressing the performance is defined. The word “performance” includes the following three metrics; the average propagation delay, the power consumption, and the area. The optimum scaling factor corresponding to the best performance is determined. It is found that under the worst-case low-to-high transition at the output (that is, the input combination that results in the longest time delay in case of logic “1” at the output), there is an optimum value for the sizing of the PDN in order to minimize the average propagation delay. The proposed figure of merit is evaluated for different cases with the results discussed. The adopted models and the drawn conclusions are verified by comparison with simulation results adopting the 45 nm CMOS technology.

In this paper, we have analyzed the full width-half maximum (FWHM) response of a uniform fiber Bragg grating (FBG) for petroleum sensor applications numerically. The analysis; which is depending on parameters such as the gratings length (Lg) and the amplitude of an induced index profile (Δn) change have successfully investigated using MATHCAD software. From the numerical simulation, there is an effect of the Lg and the Δn on the FWHM response. Results show the Lg value that effect the FWHM response is ≤7 mm. In contrast, results show that there is no effect of temperature on the FWHM response. In light of the increasing demand for a wide FWHM band within the applications of optical sensor technology, the results obtained are very important, especially in the field of petroleum industry.

In this article, a PD-type iterative learning control algorithm (ILC) is proposed to a nonlinear time-varying system for cases of measurement disturbances and the initial state errors. The proposed control approach uses a simple structure and has an easy implementation. The iterative learning controller was utilized to control a constant current source inverter (CSI) with pulse width modulation (PWM); subsequently the output current trajectory converged the sinusoidal reference signal and provided constant switching frequency. The learning controller's parameters were tuned using particle swarm optimization approach to get best optimal control for the system output. The tracking error limit is achieved using the convergence exploration. The proposed learning control scheme was robust against the error in initial conditions and disturbances which outcome from the system modeling inaccuracies and uncertainties. It could correct the distortion of the inverter output current waveform with less computation and less complexity. The proposed algorithm was proved mathematically and through computer simulation. The proposed optimal learning method demonstrated good performances.

Various methods have been exploited in the blind source separation problems, especially in cocktail party problems. The most commonly used method is the independent component analysis (ICA). Many linear and nonlinear ICA methods, such as the radial basis functions (RBF) and self-organizing map (SOM) methods utilise neural networks and genetic algorithms as optimisation methods. For the contrast function, most of the traditional methods, especially the neural networks, use the gradient descent as an objective function for the ICA method. Most of these methods trap in local minima and consume numerous computation requirements. Three metaheuristic optimisation methods, namely particle, quantum particle, and glowworm swarm optimisation methods are introduced in this study to enhance the existing ICA methods. The proposed methods exhibit better results in separation than those in the traditional methods according to the following separation quality measurements: signal-to-noise ratio, signal-to-interference ratio, log-likelihood ratio, perceptual evaluation speech quality and computation time. These methods effectively achieved an independent identical distribution condition when the sampling frequency of the signals is 8 kHz.